Professional vinyl floor strip, seal and polishing services across Sydney. Machine polishing, burnishing, hospital-grade sealer, anti-slip finish for LVT, VCT and commercial vinyl — after hours available, no lock-in contracts.
Vinyl floors in commercial environments take a relentless beating from foot traffic, trolleys, equipment, and cleaning chemicals. Over time, the protective sealer layer wears away, leaving floors looking dull, yellowed, and difficult to clean — no matter how frequently they are mopped. Once the sealer is gone, the vinyl surface itself becomes porous and susceptible to permanent staining, abrasion, and bacterial contamination that regular cleaning cannot address.
Pro Clean Corp restores commercial vinyl floors across Sydney using a complete strip, seal, and polish process — removing all old sealer and applying fresh hospital-grade sealer coats that protect the vinyl and restore a brilliant, long-lasting shine. We service LVT (luxury vinyl tile), VCT (vinyl composition tile), homogeneous vinyl sheet, and vinyl plank flooring across hospitals, schools, offices, retail stores, and industrial facilities.
With over 15 years of experience, $20M public liability insurance, and no lock-in contracts, Pro Clean Corp delivers vinyl floor polishing and restoration across Sydney to the standard commercial and institutional facilities require.
Chemical stripping removes all old, contaminated sealer — fresh hospital-grade sealer coats applied to restore a complete protective barrier and brilliant finish.
High-gloss finish on freshly sealed floors using rotary polishers and appropriate polishing pads — from satin to wet-look gloss finishes available.
Ultra-high-speed burnishing between strip cycles restores a deep wet-look gloss on sealer-finished floors — maintaining the shine that fades with daily use.
Sealer additive for wet areas, kitchens, and aged care facilities — measurable slip resistance improvement without significantly affecting floor appearance.
Free on-site assessment. Written quote within 24 hours.
Strip and seal is a two-phase floor restoration process. The strip phase uses a chemical floor stripper — applied and agitated with a single disc floor machine — to dissolve and remove all existing sealer coats from the vinyl surface. The seal phase then applies multiple fresh coats of commercial floor sealer that bond to the clean vinyl, creating a new protective layer. The result is a floor that looks new, is easier to maintain, and is protected against wear and soiling.
Strip and reseal frequency depends on foot traffic intensity. High-traffic commercial floors (hospitals, schools, supermarkets) may require stripping annually or every 18 months. Medium-traffic offices and retail environments typically need stripping every 2–3 years. Between strips, regular burnishing and recoating extends the sealer life. We assess your floor's condition and recommend an appropriate maintenance programme.
Machine polishing (using a standard rotary polisher with a polishing pad) is performed after strip and seal to bring up the initial shine on fresh sealer. Burnishing uses an ultra-high-speed (UHS) burnisher — spinning at 1,500–3,000+ RPM — to generate heat that fuses the sealer surface into a deep, wet-look gloss. Burnishing is used as a maintenance step between strip cycles to restore the shine that fades with daily cleaning and traffic.
Yes, but LVT and vinyl plank require specific products and methods. Many LVT products have a factory-applied polyurethane wear layer that should not be stripped with chemical strippers. We use LVT-compatible, pH-neutral cleaning and application of purpose-formulated LVT floor finish rather than traditional sealer. We always confirm the manufacturer's recommendations before applying any chemical to LVT.
Yes. Periodic maintenance programmes — combining regular spray buffing or burnishing with occasional recoating — extend the life of the sealer system between full strip cycles and keep floors looking consistently professional. We design maintenance programmes based on your floor type, traffic level, and daily cleaning practices, and can include vinyl floor maintenance in your regular commercial cleaning contract.
Yes. Anti-slip finish is available as a sealer additive for wet areas, commercial kitchens, aged care facilities, and any other area where enhanced slip resistance is required by WHS regulations or risk assessment. Anti-slip additives are incorporated into the sealer coats during the seal phase and provide a measurable improvement in the coefficient of friction without significantly affecting the appearance of the floor.
We provide vinyl floor polishing and strip-seal services for all types of commercial and institutional facilities across Sydney — hospitals and medical centres, schools and TAFE campuses, aged care facilities, office buildings, retail stores, supermarkets, warehouses, and strata building common areas. We work after hours and on weekends to avoid disrupting your operations during the strip, seal, and polishing process.
Free on-site assessment and written quote within 24 hours. After-hours and weekend scheduling, periodic maintenance programmes, no lock-in contracts.